E11: Furnaces, Drying Cabinets & Infrared Steriliser
FURNACES
Muffle furnace - 1150°C
Muffle furnaces are available in three sizes, 3.5 litre, 6.6 litre & 15 litre. All sizes can be supplied with either sliding or cantilever type door. The quick action sliding door can be held in any position and is ideal for ashing or similar operations. A cantilever door has an outward and upward swing with a counter-balanced handle on the right hand side (left hand side optional).
Construction
The furnaces are strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face and door. The muffle is strongly supported by a refractory mould at the front and insulating bricks at the back. It is insulated with top grade ceramic fibre blanket or non-hazardous substitutes on request. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel.
All cantilever door furnaces are fitted with a door switch for safety. Kanthal A1 Element is controlled by a microprocessor based PID Controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Options
* Volatile matter furnaces and coal testing furnaces made to A.S. 1038.4 specifications.
ProSciTech routinely sells these items below the manufacturer's retail price.
For all prices - ask
Variations available:
C - cantilever door
S - sliding door
E102 Muffle furnace, 250 x 160 x 90mm, digital PID
E152 Muffle furnace, 290 x 170 x 135mm, digital PID
E202 Muffle furnace, 435 x 230 x 150mm, digital PID
E102C Muffle furnace, 250 x 160 x 90mm, cantilever door, digital PID ask Availability
Muffle furnace - 1150°C
Muffle furnaces are available in three sizes, 3.5 litre, 6.6 litre & 15 litre. All sizes can be supplied with either sliding or cantilever type door. The quick action sliding door can be held in any position and is ideal for ashing or similar operations. A cantilever door has an outward and upward swing with a counter-balanced handle on the right hand side (left hand side optional).
Construction
The furnaces are strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face and door. The muffle is strongly supported by a refractory mould at the front and insulating bricks at the back. It is insulated with top grade ceramic fibre blanket or non-hazardous substitutes on request. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel.
All cantilever door furnaces are fitted with a door switch for safety. Kanthal A1 Element is controlled by a microprocessor based PID Controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Options
- 7 day or 24 hour timer
- Programmable Controller (16 step Yokogawa or 40 step Shimaden)
- Ramp function
- Monitory overheat cutout (separate controller + Thermo couple)
| 100 Series | 150 Series | 200 Series | |
| Power ratings | 2400 W | 3600 W | 4800 W |
| Catalogue numbers | E102C (cantilever door) | E152C (cantilever door) | E202C (cantilever door) |
| E102S (sliding door) | E152S (sliding door) | E202S (sliding door) | |
| External dimensions (mm) | 456D x 468W x 560H | E500D x 470W x 610H | 608D x 546W x 630H |
| Internal dimensions (mm) | 250D x 160W x 90H | 290D x 170W x 135H | 435D x 230W x 150H |
| Weight (kg) | 50 | 56 | 70 |
| Capacity (L) | 3.5 | 6.6 | 15 |
* Volatile matter furnaces and coal testing furnaces made to A.S. 1038.4 specifications.
ProSciTech routinely sells these items below the manufacturer's retail price.
For all prices - ask
Variations available:
C - cantilever door
S - sliding door
E102 Muffle furnace, 250 x 160 x 90mm, digital PID
E152 Muffle furnace, 290 x 170 x 135mm, digital PID
E202 Muffle furnace, 435 x 230 x 150mm, digital PID
E102C Muffle furnace, 250 x 160 x 90mm, cantilever door, digital PID ask Availability
E152C
E102C Muffle Furnace
MUFFLE FURNACE - ASHING
Ashing furnace - 1000°C
Construction
The furnaces are strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face and door. The muffle is strongly supported by a refractory mould at the front and insulating bricks at the back. It is insulated with ceramic fibre and firebricks. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel. All cantilever door furnaces are fitted with a door switch for safety.
Kanthal A1 Element is controlled by a microprocessor based PID controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Air exhaust is through an adjustable 50mm vent on top of the furnace. Airflow is up to 20 exchanges per minute at 800°C. The air inlet is through two vent tubes at the back of the furnace allowing air to pass over the external surface of the muffle through channels in the insulating bricks and into the working chamber via a gap at the top of the muffle. This gives a preheated airflow to maintain an even temperature. The heating section of muffle is set back from the door face approximately 70mm to give an even temperature from front to back of working area. The outer case is kept to minimum temperature by a surrounding air cavity.
*Applies to uniform zone within 30mm of back & 70mm from front edge of muffle liner.
ProSciTech routinely sells these items below the manufacturer's retail price.
E102CAF Ashing furnace, 320 x 160 x 90mm inquire
VOLATILE MATTER FURNACE
Volatile matter furnace to as 1038.4 - 1995
Construction
Strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face door. The muffle is supported by a refractory mould at the front and insulating bricks at the back. It is insulated with top grade Kaowool ceramic fibre blanket. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel. All cantilever door furnaces are fitted with a door switch for safety.
Kanthal A1 Element is controlled by a microprocessor based PID Controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Features
The furnace has three thermocouples: a permanently fixed stainless steel sheathed thermocouple which controls the temperature of the muffle, a ceramic sheathed thermocouple permanently located so as to position the four place crucible stand in the uniform temperature zone, and an unsheathed thermocouple which can be positioned under any of the four crucibles.
The temperature of the unsheathed thermocouple is related to the sheathed thermocouple and must be 900± 5°C. Both of these thermocouples are terminated on the front panel of the furnace for easy monitoring. The furnace has adequate heating to regain 885°C after four minutes and 900± 5°C within seven minutes of the insertion of a cold stand and its crucibles, as required by the standard.
A four place crucible stand, flue cap and floor tile are provided with the furnace.
Probe insertion ports in the door are optional.
ProSciTech routinely sells these items below the manufacturer's retail price.
E102VMF Volatile matter furnace, 250 x 160 x 90mm inquire
Ashing furnace - 1000°C
Construction
The furnaces are strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face and door. The muffle is strongly supported by a refractory mould at the front and insulating bricks at the back. It is insulated with ceramic fibre and firebricks. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel. All cantilever door furnaces are fitted with a door switch for safety.
Kanthal A1 Element is controlled by a microprocessor based PID controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Air exhaust is through an adjustable 50mm vent on top of the furnace. Airflow is up to 20 exchanges per minute at 800°C. The air inlet is through two vent tubes at the back of the furnace allowing air to pass over the external surface of the muffle through channels in the insulating bricks and into the working chamber via a gap at the top of the muffle. This gives a preheated airflow to maintain an even temperature. The heating section of muffle is set back from the door face approximately 70mm to give an even temperature from front to back of working area. The outer case is kept to minimum temperature by a surrounding air cavity.
| Specifications | 100 Series |
| Power ratings | 240V 2400W |
| Catalogue number | E102CAF |
| Dimensions (mm) | External 460D x 475W x 560H |
| Internal 320D x 160W x 90H | |
| Temperature range | Ambient to 1000°C ±2°C |
| Temperature variation | ±10°C @ 815°C* |
| Rate of ventilation | 2-20 Exchanges per minute @ 800°C |
| Weight (kg) | 70 |
*Applies to uniform zone within 30mm of back & 70mm from front edge of muffle liner.
ProSciTech routinely sells these items below the manufacturer's retail price.
E102CAF Ashing furnace, 320 x 160 x 90mm inquire
VOLATILE MATTER FURNACE
Volatile matter furnace to as 1038.4 - 1995
Construction
Strongly constructed of zinc coated steel powder coated Wedgewood blue with Hi Temp black front face door. The muffle is supported by a refractory mould at the front and insulating bricks at the back. It is insulated with top grade Kaowool ceramic fibre blanket. The steel cover around the muffle is surrounded by an air cavity and by gravity convection draws heat away from the bottom and out through the top reducing the wall temperature of the outer body. An air gap at the front and louvres on back panel allow adequate air flow to ensure a cool instrument panel. All cantilever door furnaces are fitted with a door switch for safety.
Kanthal A1 Element is controlled by a microprocessor based PID Controller complete with Auto Tune function and sensor compensation for accurate temperature control. An overtemp cutout is also provided as a standard feature.
Features
The furnace has three thermocouples: a permanently fixed stainless steel sheathed thermocouple which controls the temperature of the muffle, a ceramic sheathed thermocouple permanently located so as to position the four place crucible stand in the uniform temperature zone, and an unsheathed thermocouple which can be positioned under any of the four crucibles.
The temperature of the unsheathed thermocouple is related to the sheathed thermocouple and must be 900± 5°C. Both of these thermocouples are terminated on the front panel of the furnace for easy monitoring. The furnace has adequate heating to regain 885°C after four minutes and 900± 5°C within seven minutes of the insertion of a cold stand and its crucibles, as required by the standard.
A four place crucible stand, flue cap and floor tile are provided with the furnace.
Probe insertion ports in the door are optional.
| Specifications | 100 Series |
| Power ratings | 2400W |
| Catalogue Number | E102VMF |
| External dimensions (mm) | 456D x 468W x 560H |
| Internal dimensions (mm) | 250D x 160W x 90H |
| Weight (kg) | 50 |
ProSciTech routinely sells these items below the manufacturer's retail price.
E102VMF Volatile matter furnace, 250 x 160 x 90mm inquire
Ashing furnace
GLASSWARE DRYING CABINETS
SEM glassware drying cabinets are solidly constructed of zinc seal mild steel coated inside and out with tough white polyurethane baked enamel. The door is of tubular steel frame and full view glass which seals agains rubber extrusion. The oven sides are double walled to allow easy removal of trays and reduce heat loss. Shelf supports are adjustable. The temperature is controlled by a thermostat, ambient to 100°C. An overheat protection with push button reset is fitted.
ProSciTech routinely sells these items below the manufacturer's retail price.
Variations available:
FGD - forced convection
GGD - gravity convection
E17GD Glassware drying cabinet, 665 x 500 x 500mm
E18GD Glassware drying cabinet, 900 x 500 x 500mm
E19GD Glassware drying cabinet, 1200 x 500 x 500mm - ask
E17FGD Glassware drying cabinet, 665 x 500 x 500mm, forced convection ask Availability
SEM glassware drying cabinets are solidly constructed of zinc seal mild steel coated inside and out with tough white polyurethane baked enamel. The door is of tubular steel frame and full view glass which seals agains rubber extrusion. The oven sides are double walled to allow easy removal of trays and reduce heat loss. Shelf supports are adjustable. The temperature is controlled by a thermostat, ambient to 100°C. An overheat protection with push button reset is fitted.
| Model | Voltage | Watts | Cat. No. | No. of Shelves | Internal Dimensions HxWxD (mm) | External Dimensions HxWxD (mm) |
| 150 Litre | ||||||
| Forced convection | 240 | 1500 | E17FGD | 2 | 665 x 500 x 500 | 900 x 560 x 540 |
| Gravity convection | 240 | 1200 | E17GGD | 2 | 665 x 500 x 500 | 900 x 560 x 540 |
| 225 Litre | ||||||
| Forced convection | 240 | 2000 | E18FGD | 3 | 900 x 500 x 500 | 1130 x 560 x 540 |
| Gravity convection | 240 | 1800 | E18GGD | 3 | 900 x 500 x 500 | 1130 x 560 x 540 |
| 300 Litre | ||||||
| Forced convection | 240 | 2300 | E19FGD | 4 | 1200 x 500 x 500 | 1430 x 560 x 540 |
| Gravity convection | 240 | 2000 | E19GGD | 4 | 1200 x 500 x 500 | 1430 x 560 x 540 |
ProSciTech routinely sells these items below the manufacturer's retail price.
Variations available:
FGD - forced convection
GGD - gravity convection
E17GD Glassware drying cabinet, 665 x 500 x 500mm
E18GD Glassware drying cabinet, 900 x 500 x 500mm
E19GD Glassware drying cabinet, 1200 x 500 x 500mm - ask
E17FGD Glassware drying cabinet, 665 x 500 x 500mm, forced convection ask Availability
E19FGD
BACTIZAPPER™ INFRARED STERILISER also know as a Bacti-Cinnerator
The BactiZapper™ is designed for benchtop sterilisation of research microbiology tools.
It has an asbestos-free core element that uses infrared heating to produce 815°C (1500°F). It completely sterilises microorganisms in 5-7 seconds.
The BactiZapper uses well-proven technology to provide instant sterilisation of platinum inoculating loops, needles, glass tube/pipette mouths and various metal & borosilicate glass instruments, commonly used in microbiology research.
The ceramic heating element is safely enclosed in a perforated stainless steel guard chamber, protecting users from accidental contact with the extreme temperatures of the core area. It is compact, convenient and can be used in anaerobic and aerobic chambers.
The replacement heating element consists of the core and the steel guard chamber. The old 'head' is easily removed by undoing the hex screws at the top of the stem and uncoupling the 2 wires.
EB0900 BactiZapper™ infrared steriliser, 230V AUD375.00 Available
EB0900-HE BactiZapper™ replacement heating element, 230V AUD170.00 Available
EB0900-LH BactiZapper™ loop holder attachment AUD59.00 Available
EB0900-SD BactiZapper™ slide dryer attachment AUD92.00 Available
The BactiZapper™ is designed for benchtop sterilisation of research microbiology tools.
It has an asbestos-free core element that uses infrared heating to produce 815°C (1500°F). It completely sterilises microorganisms in 5-7 seconds.
The BactiZapper uses well-proven technology to provide instant sterilisation of platinum inoculating loops, needles, glass tube/pipette mouths and various metal & borosilicate glass instruments, commonly used in microbiology research.
The ceramic heating element is safely enclosed in a perforated stainless steel guard chamber, protecting users from accidental contact with the extreme temperatures of the core area. It is compact, convenient and can be used in anaerobic and aerobic chambers.
The replacement heating element consists of the core and the steel guard chamber. The old 'head' is easily removed by undoing the hex screws at the top of the stem and uncoupling the 2 wires.
| Maximum temperature | 815°C |
| Sterilisation time | 5-7 seconds |
| Chamber diameter | 14mm |
| Chamber length | 100mm |
| Dimensions external (WxDxH) | 100 x 150 x 165mm |
| Weight | 1.4kg |
| Electrical | 230V 50Hz |
EB0900 BactiZapper™ infrared steriliser, 230V AUD375.00 Available
EB0900-HE BactiZapper™ replacement heating element, 230V AUD170.00 Available
EB0900-LH BactiZapper™ loop holder attachment AUD59.00 Available
EB0900-SD BactiZapper™ slide dryer attachment AUD92.00 Available
[click to enlarge]
Slide dryer, loop holder attachments
| 
|
