• Shipping dimensions and weights of incubators, ovens, furnaces and glassware drying cabinets
• Data sheet on types of ovens/ incubators
• Digital PID control unit & solid state heat controller
• Thermometers are available on page E5
• Hanna thermometers are available on page E3
• Laboratory tongs on page T10
• EDCG Cabinet fitting for dry gas use on page E12 is required to bleed any gas into desiccators, incubators or ovens.

ProSciTech routinely sells these items below the manufacturer's retail price.

Construction of Laboratory Incubators and Ovens

Standard units 240V 50Hz AC.
* Larger capacity units available.
* Special types made to customer's specifications
* External finish is tough, easy to clean epoxy gloss
* Chamber is satin finish stainless steel
* Wire type trays with incubators
* Robust hinges support door without sag
* Door seals are of durable silicone rubber.
* An inner glass door seals against a rubber seal and is held by an effective catch and hinges
* External casing is made of zinc-seal steel
* Insulated with 50mm of fibreglass

---

Temperature variations in Incubators and Ovens and Control options:

Thermostatic control (dial setting which, from experience, provides accurate, reliable temperature) is standard. Alternatively, digital PID control with digital display (dial temperature and feedback temperature digital display) are available. The latter makes a thermometer redundant.
Ovens and incubators are constructed in different ways to achieve even temperature distribution and quick temperature recovery at varying cost. All but the smallest size incubator and oven are available with the different heat distribution systems. The smallest oven and incubator are supplied with gravity convection only. Gravity convection is cheapest, though it does not result in best air circulation and greatest temperature uniformity within the chamber. In a given spot the temperature will, however, be constant within about 0.3^oC. Mechanical convection (a stirrer) markedly improves temperature uniformity. Best, but most expensive, is forced air convection within a chamber jacket. This type of incubator may fluctuate at 37^oC by +/- 0.1^oC in one spot (oven at 100^oC by 0.5^oC). Within the chamber, the temperature can vary by +/-0.5^oC (ovens +/- 2^oC). Variations of forced air convection systems are side, up and down draft ovens and incubators.
Options for various temperature regulating and forced circulating systems are available for all incubators and ovens - except the smallest, the E14 (incubator) and E24 (oven).

---

Shipping of Ovens, Incubators and Hot Plates:
Our quotations include shipping cost of these items within Australia. For overseas orders please ask for a price including freight.
Shipping dimensions and weights of incubators, ovens, hotplates, waterbaths and steambaths.

INCUBATORS

Gravity & Forced Convection Incubators

EXTERIOR: Tough, easy to clean semi-gloss finish. Powder coated cream or to customer's requirements.

OUTER DOOR: Well supported with robust hinges to give long life and eliminate sag. The door seals with a magnetic surround and non protruding easy opening stainless finger strip.

CONTROL PANEL: Mounted above door to give eye level vision of instruments. Solid state temperature control with digital readout and touch switch temperature selection. Controller easy to remove for quick replacement if needed. A push button reset overheat thermostat is mounted on the control panel.

INSULATION: 50 mm thick grade fibreglass for minimum heat loss.

INTERIOR: All stainless steel with clear floor space for special equipment.

INNER DOOR: The glass door is fitted with robust hinges. A catch ensures positive seal against rubber surround.

SHELVES: Chrome plated straight wire type shelves allow maximum circulation.

FORCED CONVECTION: Fan motor, rubber mounted for very quiet running.

Incubator data

Model No.	Temperature Range	Internal Dimensions HxWxD mm	External Dimensions HxWxD mm	Capacity Litres	No. Shelf Positions	No. Shelves Supplied	Power Rating (Watts)
E14	AMB.-70°C	200 x 250 x 200	400 x 360 x 300	10	3	2	200
E15	AMB.-80°C	350 x 300 x 300	650 x 430 x 420	31.5	3	2	200
E16	AMB.-80°C	460 x 380 x 350	750 x 510 x 460	60	4	2	300
E17	AMB.-80°C	600 x 500 x 500	900 x 630 x 620	150	5	3	600
E18	AMB.-80°C	900 x 600 x 500	1200 x 730 x 620	270	6	4	950
E19	AMB.-80°C	1200 x 600 x 600	1500 x 730 x 700	432	8	4	1300

Standard units 240V 50Hz AC.
Typical Temperature Fluctuation ±0.1°C at 37°C.
Typical Temperature Variation ±0.5°C at 37°C.

GRAVITY CONVECTION INCUBATORS
Spiral type elements in the heating chamber are used for even temperature distribution. Accurate control is obtained with either a snap action hydraulic thermostat solid state analog instrument or digital indicator controller. This type can be supplied with stirrer (mechanical convection).

LARGE CAPACITY INCUBATORS
Information on incubators with a greater working volume will be provided on request.

*Special types made to customer's specifications*

ProSciTech routinely sells these items below the manufacturer's retail price.

Incubators may be equipped to suit requirements and budgets.
Variations available:
G - gravity convection, thermostat temperature control
GD - gravity convection, digital PID temperature control
M - mechanical convection, thermostat
MD - mechanical convection, digital PID
FD - forced convection, vertical draught, digital PID
M and MD are available for sizes 15, 16 and 17.

Digital PID
PID stands for Proportional-Integral-Derivative control.
Digital PID may also be supplied 'programmable' or the digital control may be supplied with a computer interface for computer control.
The Yokogawa 16 step programmable PID has 1 program of 16 steps, 8 ramps and 7 dwells. Example: Start at ambient temperature (25°C, first dwell), move to 50°C in 5 minutes with a first ramp of 5C°/min. Stay at 50°C for 30 minutes (second dwell) before moving to 100°C in 5 minutes with a second ramp of 10C°/min etc.
The Shimaden 40 step allows 1 program of 40 steps, 2 programs of 20 steps each, or 4 programs of 10 steps each. Frequently used programs can be stored and used again without having to reprogram the PID.

User note - Dry nitrogen operation

EDCG Cabinet fitting for dry gas use on page E12 is required to bleed any gas into desiccators, incubators or ovens.

E14 Incubator, amb-70°C, 200 x 250 x 200mm
E15 Incubator, amb-80°C, 350 x 300 x 300mm
E16 Incubator, amb-80°C, 460 x 380 x 350mm
E17 Incubator, amb-80°C, 600 x 500 x 500mm
E18 Incubator, amb-80°C, 900 x 600 x 500mm
E19 Incubator, amb-80°C, 1200 x 600 x 600mm

E14G Incubator, 200 x 250 x 200, gravity convection ask Availability

MINI DIGITAL INCUBATOR
With digital temperature control, the MyTemp™ incubators provide convenient "set and walk away" operation, eliminating the need for external thermometers and repetitive "fine tuning" of an analogue control knob. Simply choose the desired temperature and the incubator immediately begins to heat up (or cool down, -HC model only) while accurately monitoring the chamber temperature and conveniently displaying the temperature in real time on the large LED control panel. Despite a modest footprint of 330 x 368mm, the MyTemp incubators feature large internal chambers, capable of storing flasks and bottles up to 2 litre. In addition, the incubators include two adjustable/ removable shelves for increased capacity. A mini nutating rocker (supplied with both flat and dimpled mats) is also available for agitation of samples during incubation.

Features

• Digital temperature control
• supplied with universal power supply, converting mains to 12VDC
• supplied with car power adapter cord
• Personal sized, 330 x 368mm footprint (20L)
• Accepts bottles and flasks up to 2L
• Two models: Heat only or heat/cool
• Optional mini shaker available for agitation of samples

Temperature range (H)	Ambient +1°C to 60°C
Temperature range (HC)	5°C lowest (achieves ambient -15°C) to 60°C*
Temperature accuracy	0.5°C (at 37°C)
Temperature uniformity	+/- 1°C (at 37°C)
Temperature increment	1°C
Platform dimensions	235 x 290mm
Operating temperature range	+4 to +65°C
Dimensions (w x d x h)
Exterior	335 x 370 x 475mm
Interior	260 x 235 x 325mm
Capacity	20L
Weight	6.5 kg
Warranty	2 Years
Electrical	universal supply 100 - 230V, 50 or 60Hz
Warranty	2 Years

* Minimum temperature is 5°C. This is achieved if ambient is 20°C room.

EBH2200-H MyTemp mini digital incubator, with heating only AUD791.00 Availability
EBH2200-HC MyTemp mini digital incubator, with heating and cooling ask Available
EBH2200-SH Extra shelf, for EBH2200, 267 x 203mm AUD55.00 Available
EBH3D1020 Mini nutating rocker with flat cord, 203 x 152mm platform AUD455.00 Availability

REFRIGERATED INCUBATORS

STANDARD RANGE - MODIFIED DOMESTIC FRIDGE

FEATURES:

- Digital PID temperature control and solid state relay switching.
- Fan forced convection.
- Low and high temperature safety thermostats.
- Multiple shelf positions.
- Temperature range: 4-45°C ± 0.75°C
- "Clean Back" Internal condenser system.

EXTRAS

Diurnal lighting; timer; internal perspex door, internal power outlets, cable ports, gas purge inlets, programmable controller.

FREEZER INCUBATORS

Special units made to customer requirements

FREEZER INCUBATOR: Upright


- Digital PID temperature control and solid state relay switching.
- Fan forced convection.
- Low temperature safety thermostat.
- Temperature range:- 8°C to ambient ±0.5°C.

Options - Chest freezer units available with external control box

ProSciTech routinely sells these items below the manufacturer's retail price.
*Special units made to customer specifications

SPECIFICATIONS

Cat. No.	Capacity (pre-modifications) (L)	Capacity (after modifications) (L)	External Dimensions HxWxD (mm)	Internal Dimensions HxWxD (mm)	No. of Shelves	Packed Dimensions HxWxD (mm)	Packed Weight (kg)
ERI40	50	40	656 x 466 x 493	400 x 350 x 350	2	780 x 500 x 520	30
ERI90	120	90	819 x 525 x 550	500 x 430 x 420	2	1020 x 550 x 575	40
ERI235	270	235	1595 x 525 x 550	1295 x 430 x 420	5	1790 x 550 x 575	70
ERI330	370	330	1425 x 635 x 668	1130 x 540 x 540	4	1620 x 660 x 700	80
ERI390	420	390	1600 x 680 x 680	1300 x 580 x 515	4	1800 x 710 x 710	85
EFI90	120	90	970 x 500 x 600	640 x 400 x 350	3	1100 x 525 x 625	40

ERI40 Refrigerated incubator, 400 x 350 x 350mm
ERI90 Refrigerated incubator, 500 x 430 x 420mm
ERI235 Refrigerated incubator, 1295 x 430 x 420mm
ERI330 Refrigerated incubator, 1130 x 540 x 540mm
ERI390 Refrigerated incubator, 1300 x 580 x 515mm
EFI90 Freezer incubator, 640 x 400 x 350mm, amb. to -8°C

ERI40 Refrigerated incubator, 400 x 350 x 350mm, 40L ask Availability

CLINILAB INCUBATORS

EIGCL Clinilab Incubator
A specially designed portable incubator for use in clinical, public health, and small industrial labs. Also suitable for use in school and university laboratories. Double wall construction. The exterior wall is made of heavy gauge zinc coated steel finished in polyurethane enamel. The interior wall is stainless steel. Accurate temperature control is maintained by a hydraulic thermostat. Fitted with a carrying handle, rubber feet, a removable thermometer 0 to 100°C and a hinged door. Included is a combination Petri dish rack and test tube holder, 210 mm x 117 mm, with four shelves and 32 holes, each 17 mm diameter, for test tubes.

Temperature Range	5°C above ambient to 70°C
Temperature Fluctuation	±0.5°C from 25 to 70°C
Internal Dimensions (mm)	198 H x 214 W x 120 D
External Dimensions (mm)	316 H x 260 W x 147 D
Working Volume (L)	5
Rating	40 W 240 V 50 Hz

EIGCLD Clinilab Incubator
Similar to Cat. No IGCL Clinilab Incubator but designed for operation from 12V D.C. or 240 V 50 Hz (Not illustrated).

EIGCL Clinilab incubator, 198 x 214 x 120mm
EIGCLD Clinilab incubator, 198 x 214 x 120mm, dual voltage inquire

OVENS

10 LITRE LABORATORY OVEN AND INCUBATOR
CONSTRUCTION
The inner working chamber is constructed of satin finish stainless steel with three shelf positions. Two chrome plated perforated trays are supplied.

The door is hinged on the left side with positive catch to keep it closed against a silicone rubber seal. The incubator has an acrylic inner door fitted.

A vent tube is situated in the top of the oven. The outer body is constructed of zinc seal steel, finished with light cream enamel.

	Oven - Cat. No. E24G	Incubator - Cat. No. E14G
Internal Dimensions (mm)	200H x 255W x 200D	200H x 255W x 200D
External Dimensions (mm)	390 H x 362 W x 300 D	390 H x 362 W x 300 D
Rating	240V x 400W x 50Hz	240V x 200W x 50Hz
Temperature	Ambient to 150°C	Ambient to 70°C
Temperature Fluctuation	±2°C at 100°C	±0.3°C at 37°C
Temperature Control	Thermostat	Thermostat

OPTIONS:
- Thermostat or digital PID control
- Fan forced

ProSciTech routinely sells these items below the manufacturer's retail price.

GRAVITY AND FORCED CONVECTION OVENS

• Long laboratory tongs on T10

EXTERIOR
Attractive gloss finish baked enamel.

OUTER DOOR
Well supported with robust hinges to give long life and eliminate sag. The door seals against a silicone rubber extrusion with a positive chrome plated finger tip release door catch.

CONTROL PANEL
A solid state digital controller with touch switch temperature selection working in conjuction with a zero switching solid state relay. A push button reset overheat thermostat is mounted on the control panel.

INSULATION
65 mm thick is high grade fibre glass insulation is used for temperature up to 300°C.

INTERIOR
All stainless steel.

SHELVES
Chrome plated straight wire type give maximum strength and ventilation.

FORCED CONVECTION
Fan motor, rubber mounted in bottom cabinet for very quiet running.

VENTILATION
An adjustable ventilation port is mounted on top of oven.

OVEN DATA

Model No.	Temp. Range	Internal Dimensions HxWxD (mm)	External Dimensions HxWxD (mm)	Capacity (L)	No. Shelf Positions	No. Shelves Supplied	Power Rating (W)
E24	40-150°C	200 x 250 x 200	400 x 360 x 300	10	3	2	400
E25	40-200°C	350 x 300 x 300	750 x 490 x 450	31.5	3	2	1000
E26	40-200°C	450 x 380 x 350	850 x 570 x 500	60	4	2	1500
E27	40-200°C	600 x 500 x 500	980 x 690 x 650	150	5	3	2000
E28	40-200°C	900 x 600 x 500	1290 x 790 x 650	270	6	4	3000
E29	40-200°C	1200 x 600 x 600	1560 x 790 x 740	432	7	4	4500
E35	40-300°C	350 x 300 x 300	750 x 490 x 450	31.5	3	2	1300
E36	40-300°C	450 x 380 x 350	850 x 570 x 500	60	4	2	1750
E37	40-300°C	600 x 500 x 500	980 x 690 x 650	150	5	3	2800
E38	40-300°C	900 x 600 x 500	1290 x 790 x 650	270	6	4	3500

Standard units 240V 50Hz AC.

GRAVITY CONVECTION OVENS
Gravity convection type ovens have spiral type elements distributed in heating chamber for even heating. This type of oven can be supplied with stirrer (mechanical convection) or as forced convection and can be fitted with snap action thermostat or digital PID indicator temperature controllers.

FORCED CONVECTION OVENS
Typical instrument temperature fluctuation ±0.5°C at 100°C. Typical temperature variation ±2°C at 100°C.

TEMPERATURE FLUCTUATION
The short term change in temperature at any position in the oven working space.

TEMPERATURE VARIATION
The difference between the temperature at the centre of the oven and at any other position in the working chamber.

A range of sizes and types is available to suit the varying requirements of individual users. Higher temperature operating standards can be met and certified tests can be made if required. Heavy duty industrial ovens are made to customer specifications.

VERY HOT OVENS
The 300°C oven designs can be modified to cope with higher temperatures. These only come with forced convection and digital PID. See table for a few examples. Other sizes in these 3 temperature ranges are available, please ask for a quote.

Model No.	Temperature Range	Internal Dimensions HxWxD mm
E45FD	40-400°C	350 x 300 x 300
E55FD	40-500°C	350 x 300 x 300
E65FD	40-600°C	350 x 300 x 300

ProSciTech routinely sells these items below the manufacturer's retail price.

Variations available:
G - gravity convection, thermostat temperature control
GD - gravity convection, digital PID temperature control
FS - forced convection, side draught, thermostat
FSD - forced convection, side draught, digital PID
F - forced convection, vertical draught, thermostat
FD - forced convection, vertical draught, digital PID

Digital PID may also be supplied 'programmable' or the digital control may be supplied with a computer interface for computer control.
Other additions including gas supplies and explosion relief valve in solvent drying ovens are available - please advise your requirements and we'll find a solution.

E24 Laboratory oven, 40-150°C, 200 x 250 x 200mm
E25 Laboratory oven, 40-200°C, 350 x 300 x 300mm
E26 Laboratory oven, 40-200°C, 450 x 380 x 350mm
E27 Laboratory oven, 40-200°C, 600 x 500 x 500mm
E28 Laboratory oven, 40-200°C, 900 x 600 x 500mm
E29 Laboratory oven, 40-200°C, 1200 x 600 x 600mm
E35 Laboratory oven, 40-300°C, 350 x 300 x 300mm
E36 Laboratory oven, 40-300°C, 450 x 380 x 350mm
E37 Laboratory oven, 40-300°C, 600 x 500 x 500mm
E38 Laboratory oven, 40-300°C, 900 x 600 x 500mm
E45FD Laboratory oven, 40-400°C, 350 x 300 x 300mm
E55FD Laboratory oven, 40-500°C, 350 x 300 x 300mm
E65FD Laboratory oven, 40-600°C, 350 x 300 x 300mm

E24G Laboratory oven 200 x 250 x 200mm, gravity convection ask Availability

MINIMUM FREE SPACE OVEN

This oven conforms to the requirements of BS 1016 and has a working chamber of 274 x 158 x 28mm.

The working chamber is inside an outer chamber, which contains the heating elements.

The sensing element for the control systems is attached to the outside of the working chamber.

The temperature controller switches power to the elements via a solid state relay. Maximum continuous working temperature is 200°C. Temperature fluctuation (under normal conditions) is within 0.25°C. This design gives extremely uniform conditions within the oven, very close temperature control and a high degree of reproducibility of results.

Oven temperature can be checked by inserting a thermometer at the back of the oven. The door is fitted with a silicone rubber gasket, providing an excellent seal.

The nitrogen inlet is situated at the top rear of the oven. It is connected by a copper tube, passing through the heating chamber, to the oven proper, ensuring that the nitrogen is at the correct temperature before being admitted to the oven. The gas outlet is at the top front of the working chamber.
Samples are placed inside the MFSO, then heated to the required temperature. After heating they are removed and placed into the desiccator to cool, with the nitrogen also connected to the desiccator.

The desiccator for use with the oven, consists of a welded steel case with a thick bottom to give high heat capacity and to reduce cooling time. Inlet and outlet tubes are provided at the front and rear to allow for the passage of nitrogen.

Dimensions overall	373H x 300W x 380D mm
Ratings	240V 1250W

ProSciTech routinely sells these items below the manufacturer's retail price.

EMFSO Minimum free space oven, 274 x 158 x 28mm - ask

VACUUM OVENS

Temperature uniformity within a chamber is more difficult to achieve in a vacuum - since fans are ineffective and convection currents do not form without air. In a large chamber this could result in over 10 degrees variation. Heating elements under each shelf and separate temperature controls can reduce that variation markedly. Please ask for heated shelves if you require greater temperature uniformity.

Vacuum ovens are also available for higher temperatures - 300, 350 and even 400 degrees. The hotter vacuum ovens require modifications to the window and vacuum sealing, additional to the obvious insulation, elements controls. Only the largest vacuum oven (72 litres) is supplied with a safety polycarbonate shield. These shields are available options for the smaller ovens and they are especially recommended for the hotter ovens.

Vacuum connection on all vacuum ovens are 12.5mm (1/2") and gas inlets 9.5mm (3/8") unless otherwise requested.
Vacuum pump: All vacuum ovens require a vacuum pump. VF3-220 on page V2 is suitable for most purposes. Vacuum pump on V2

12L VACUUM OVEN
Features
- Double wall construction with stainless steel rectangular working chamber.
- Self compensating door seal with silicone rubber gasket.
- Exterior finished in scratch resistant baked enamel.
- Walls insulated with fibreglass.
- Observation window 200 x 200 mm wide made of tempered glass 10 mm thick allows a full view of the oven working space. Choice of single perforated aluminium shelf located centrally or two shelves spaced 70mm apart.
- Elements are mounted on an aluminium surround against the outer walls of the stainless steel working chamber.
- Two needle valves with insulated handles for vacuum and bleed use are mounted on the top of the oven with a vacuum gauge.
- Operating controls and a pilot light are located beneath the oven door.
- Temperature is controlled by a thermostat.
- Solid state control for finer temperature differential and easier temperature setting can be fitted if required.
- All solid state control ovens fitted with overtemp cutout thermostat.

SPECIFICATIONS

Temperature Control	Thermostat	Digital PID
Catalogue No.	EVAC12	EVAC12D
Temperature Range	35 to 220°C	Ambient to 220°C
Temperature Sensitivity	Approximately 2°C	0.5°C
No. of Shelves	1 or 2	1 or 2
Internal Size HxWxD	200 x 200 x 300mm	200 x 200 x 300mm
External Size HxWxD	480 x 340 x 420mm	480 x 340 x 420mm
Working Volume	12L	12L
Power Rating	650W, 240V, 50Hz	650W, 240V, 50Hz

ProSciTech routinely sells these items below the manufacturer's retail price.

EVAC12 Vacuum oven, 220°C, 200 x 200 x 300mm, thermostat

EVAC12D Vacuum oven, 220°C, 200 x 200 x 300mm, digital PID ask Availability

30L VACUUM OVEN

Features
- Double wall construction with stainless steel rectangular working chamber.
- Self compensating door seal with silicone rubber gasket.
- Exterior finished in scratch resistant baked enamel.
- Walls insulated with fibreglass.
- Observation window 300 x 300mm wide made of tempered glass 13mm thick allows a full view of the oven working space.
- Choice of single perforated aluminium shelf located centrally or two shelves spaced 100mm apart.
- Elements are mounted on an aluminium surround against the outer walls of the stainless steel working chamber.
- Two valves with insulated handles for vacuum and bleed are mounted on the control panel with a vacuum gauge to - 100 KPa.
- Temperature is controlled by a thermostat.
- Choice of analog or digital solid state control for finer temperature differential and easier temperature setting can be fitted if required.
- All solid state control ovens fitted with overtemp cutout thermostat.
- 300°C units available.

Specifications

Temperature Control	Thermostat	Digital PID
Catalogue No.	EVAC30	EVAC30D
Temperature Range	35 to 220°C	Ambient to 220°C
Temperature Sensitivity	Approximately 2°C	0.5°C
No. of Shelves	1 or 2	1 or 2
Internal Size HxWxD	300 x 300 x 350mm	300 x 300 x 350mm
External Size HxWxD	540 x 460 x 480mm	540 x 460 x 480mm
Working Volume	30L	30L
Power Rating	1250W	1250W

EVAC30 Vacuum oven, 220°C, 300 x 300 x 350mm, thermostat

EVAC30D Vacuum oven, 220°C, 300 x 300 x 350mm, digital PID ask Availability

72L VACUUM OVEN

- Double wall construction with stainless steel rectangular working chamber.
- Self compensating door seal wih silicone rubber gasket.
- Exterior finished in scratch resistant baked enamel.
- Walls insulated with fibreglass.
- Observation window 380 x 380mm wide made of tempered glass 13mm thick allows a full view of the oven working space.
- Shatter resistant Polycarbonate safety shield.
- Fitted with four runners to accept three removable perforated aluminium shelves.
- Elements are mounted on an aluminium surround against the outer walls of the stainless steel working chamber.
- Two valves with insulated handles for vacuum and bleed use are mounted on the control panel with a vacuum gauge to - 100 kPa.
- Temperature is controlled by a thermostat.
- Choice of analog or digital solid state control for finer temperature differential and easier temperature setting can be fitted if required.
- All solid state control ovens fitted with overtemp cutout thermostat.
- 300°C units available.

Specifications

Temperature Control	Thermostat	Digital PID
Catalogue No.	EVAC72	EVAC72D
Temperature Range	35 to 220°C	Ambient to 220°C
Temperature Sensitivity	Approximately 2°C	0.5°C
No. of Shelves	3	3
Internal Size HxWxD	380 x 380 x 500mm	380 x 380 x 500mm
External Size HxWxD	640 x 580 x 650mm	640 x 580 x 650mm
Working Volume	72L	72L
Power Rating	2400W	2400W

ProSciTech routinely sells these items below the manufacturer's retail price.

EVAC72 Vacuum oven, 220°C, 380 x 380 x 500mm, thermostat

EVAC72D Vacuum oven, 220°C, 380x380x500mm, digital PID ask Availability